|
GENUINE PARTS FOR BEST PERFORMANCE |
|
Gemini Saw Manufacturers the Taurus and Apollo Series of Ring Saws |
Sunshine Offers only Genuine
Gemini Saw Blades and Replacement Parts
Be assured that you are buying only
genuine parts made by Gemini Saw for their Taurus and Apollo Rings
Saws. Unlike other sources on the web, Sunshine Glassworks sells
only American made Genuine Gemini.
We keep an extensive inventory of
replacement parts for your saw so we may ship to you ASAP |
|
QUICK INDEX FOR
THIS PAGE
BLADES
PARTS |
HAVE A
DIFFERENT GEMINI SAW?
CLICK HERE for Taurus 3 Saw Parts
CLICK HERE for Apollo Saw
Blades and Parts |
|
SAW BLADES FOR TAURUS II.2 SAWS |
|
  |
TAURUS II.2 BLADE AND PARTS KIT
This kit includes everything you will need for a complete overhaul
of your Taurus II.2 Saw.
Includes the standard 0.072in diameter blade plus four red and three
yellow grommets, one hole reducer plug, a blue pulley with bearing,
five R2 bearings and a drive belt. As long as you're replacing the blade, it is time
to do the overhaul!
to addresses in the USA
$189.99 Order #03819
Standard Blade Cross Section |
|
Standard Blade |
TAURUS II.2 BLADE
0.072in diameter blade, as supplied with saw when you bought it.
Recommended for glass 3/8" or less thick. Not recommended for
ceramic tile, or materials over 3/8" thick.
Comes
with four red and three yellow grommets and one hole reducer for like new performance
to addresses in the USA
$114.99 Order #03811
Standard Blade Cross Section |
|
Slim Blade |
TAURUS II.2 SLIM BLADE
0.062in diameter blade, is extra thin. Used for cutting tiny shapes
or where a very thin kerf is required. Note: This blade is lighter
than the standard blade and requires a lighter touch when using.
Comes with four red and three yellow grommets plus one hole
reducer.
to addresses in the USA
$119.99 Order #03812
Slim Blade Cross Section |
|
Blade Separated
Blade Snapped Tight
|
TAURUS II.2 SEPARATING BLADE
0.072in diameter blade, but with a trick! This is the same high
quality Gemini blade, but with a special coupling. Used to cut
internally (like the hole in a donut) without a lead-in cut. Drill a
small hole, pass the blade through the hole and snap together. Saw
your internal cut, and separate the blade to free your piece.
Also comes with four red and three yellow grommets and one hole
reducer.
to addresses in the USA
$114.99 Order #03813
Separating Blade Cross Section |
|
Dichroic Blade |
TAURUS II.2 DICHROIC BLADE
Gemini has taken an extra skinny 0.058in diameter blade and coated it with extra fine
diamonds. This results in a blade perfectly suited for working with
dichroic and iridized coatings. The combination of thin blade and
fine diamonds makes for a smooth edge that allows you to fire at a
lower temperature to achieve a fire polished edge.
Comes with four red and three yellow grommets and one hole reducer.
to addresses in the USA
$119.99 Order #03814
Dichroic Blade Cross Section |
|
A NOTE REGARDING GENUINE GEMINI BLADES SOLD AT
SUNSHINEGLASS.COM
We have seen other imported blades on the market that are being provided for Gemini Saws.
These blades are only slightly less costly than the genuine article and
they don't include the required grommets. Stick with Genuine American Made Gemini
Parts to assure yourself the accurate blade tracking and long life that you will get
with the blades made expressly for your Taurus saw. |
|
REPLACEMENT PARTS FOR TAURUS II.2 SAWS |
|
|
DRIVE BELT FOR RING SAWS
$48.99, Order #03820
|
|
 |
RED GEAR GROMMETS FOR TAURUS II.2
SAWS
Sold individually. Your saw uses TWO.
$3.49 each, Order #03822
|
|
 |
YELLOW GROMMETS FOR TAURUS II.2
SAWS
Sold individually. Your saw uses THREE.
$3.49 each, Order #03821
|
|
 |
R2 BEARINGS FOR TAURUS II.2
SAWS
Sold individually. Your saw uses FIVE, one inside each yellow and
red grommet.
$6.99 each, Order #03823
REPLACEMENT SCREWS FOR R2 BEARINGS
Sold individually. Factory Part # M3.
$0.35 each, Order #03830
|
|
These pulleys go in positions 1,2,3 and
5, all of the upper pulleys |
BLUE PULLEYS WITH
RAISED RAILS & BEARINGS
Sold individually. Your saw uses FOUR, however it is rare that ALL
will fail. Generally only one or two are needed - the ones that are
most exposed to water.
$29.99 each, Order #03826
|
|
This pulley goes in position 4, the
lowest pulley |
BLUE PULLEY WITH
STANDARD RAILS & BEARINGS
Sold individually. Your saw uses ONE and it goes on the belt
tensioner in position #4 (the lowest pulley). Pulleys above with raised rails will NOT fit in position #4.
$29.99 each, Order #03825
|
|
 |
HOLE REDUCERS
Sold individually. Your saw uses ONE.
$3.29 each, Order #03809
|
|
 |
DRIVE PULLEY
Sold individually. Your saw uses ONE.
$15.99 each, Order #03817
|
|
SPECIAL NOTE: The #1037 Raceway Strips,
#0034 Spring, #1035 L-Bracket and #0015 Replacement Work Surface have
been discontinued by the factory and are no longer available. |
